MATERIAL SAFETY DATA SHEET
(updated 28/06/2005)
Drainchem
P.O. Box 5001 Sandhurst East 3550
Phone: 03 5448 4355 Mobile: 0409 850 577
Click Here to Download the Vaporooter MSDS in PDF Format
PRODUCT NAME: SANAFOAMŪ VAPOROOTERŪ (restricted use product)
EPA Registration No: 1015-70
Labels: Sodium methyldithiocarbarnate 30.00%
Inert ingredients 70.00%
100.00%
Dichlobenil 50W 50.00%
Inert ingredients 50.00%
100.00%
Chemical Names: Sodium methyldithiocarbanate, metam-sodium CAS 137-42-8
2.6-dichlorobenzonitrile, dichlobenil CAS 1194-65-6
also contains a small amount of isopropyl alcohol CAS 67-63-0
Product Description: The fiberboard box holds 2 containers: a 850 grams plastic bag containing dichlobenil POWDER
and a 20 Litre plastic container of the metam-sodium/foaming agent solution. When applicable,
the plastic container contents will be referred to as the LIQUID and the plastic bag contents as
the POWDER.
SECTION 1 – PHYSICAL DATA
Physical properties: LIQUID POWDER
Boiling Point: ND NA
pH (5% solution): 7.5 - 9.5 NA
Specific Gravity: 1.15 (H2O=1) NA
Melting Point: NA NA
Vapor Density: ND NA
Vapor Pressure: NA NA
Evaporation Rate: NA NA
Appearance & Odor: light-green to yellow tan powder
sulfur-like slightly aromatic
Solubility in Water: Miscible Insoluble, dispersible
(ND-not determined, NA-not applicable)
SECTION II – FIRE AND EXPLOSION HAZARD DATA
Flash Point (Test Method): 65* C (PMCC)
This Flashpoint results from the presence of a small quanity of isopropyl alcohol (less than 1%);
the product is nonflammable.
Extinguishing Media: Water
Special Fire Fighting Procedures: Wear full face, self-contained breathing apparatus and impervious protective clothing. Evacuate
non-essential personnel from the area. The fiberboard boxes contain plastic containers, so cool
with a water spray to avoid container rupture. The breakdown products resulting from high heat
are irritating to the respiratory tract and may cause breathing difficulty and pulmonary edema.
Run off from fire control of dilution with water may cause pollution or contamination of building,
grounds and equipment.
SECTION III – REACTIVITY DATA
These products are stable under normal sgtorage conditions.
Avoid mixing with acidic material as evolution of Hydrogen Sulfide may occur.
The POWDER may decompose on exposure to bases.
The LIQUID is corrosive to brass, copper, zinc and aluminum.
The product will decompose in extreme heat. There is no idication of hazardous polymerization.
SECTION IV – HEALTH HAZARD DATA
The principal routes of exposure are skin contact, eye contact or inhalation. Irritation may result from skin or eye contact with either the LIQUID or the POWDER.
No data have been identified which address medical conditions that are generally recognized as being aggravated by exposure to this product.
FIRST AID:
Eye contact: Flush eyes with water for at least 15 minutes and get medical attention if eye irritation persists.
Skin contact: Immediately remove contaminated clothing or shoes and flush with plenty of water to avoid skin
irritation. Inhalation in confined spaces, such as tanks and manholes: Remove to fresh air.
If breathing has stopped start artificial respiration procedures, and get medical attention immediately.
Ingestion: Give several glasses of water. Do not induce vomiting. Get medical attention immediately.
These materials are not listed in accepted cancer registries, such as NTP or IARC.
SECTION V – SPILL OR LEAK PROCEDURES
Use appropriate safety equipment when dealing with spills or leaks. Add absorbtivee granules, such as litter, and sweep up the absorbants. Place in a waste disposal container for safe and legal disposal. Then clean area with a minimum amount of water.
For container disposal, triple rinse the containers and place rinse water into the application equipment solution tank or sanitary sewer manholes. Puncture or cut container in three places and dispose of container in a sanitary landfill. Ensure that all federal, state and local regulations for disposal are followed.
Do not hose spillage onto adjacent planted areas. These herbicides may adversely affect desirable lawns, shrubs or trees. Foam should be shoveled off planted aresas immediately.
SECTION VI – SPECIAL HANDLING INFORMATION
Eye Protection: Avoid eye contact with this material. Use of face shield and glasses or goggles is recommended.
Skin Protection: Avoid skin contact with this material for it can be a severe skin irritant if not washed off. Use
gauntiet-type unlined rubber gloves and long-sleeved shirts.
Respiratory Protection: Avoid breathing vapor or mist. Use a self-contained breathing apparatus in confined spaces, such
as tanks and manholes. Ensure good ventilation in manufacturing and use areas. A NIOSH/MESHA
approved pesticide respirator with pre-filter is useful to avoid mists or dust fumes. Examples of
NOSH/MSHA respirators for this use are:
Wilson TC-23C-751, TC-23C-747, TC-23C-791 and TC-23C-792
North TC-23C-74/190
Easi-Care (3M) #7300S NSN 4240-01-246-5404
This equipment must be worn if a pugent sulfurous odor persists. Always read respirator instrustion
booklet for your personal respirator before using.
Other: A large volume of water (10 gallons or more) should be available to wash any spills off personnel.
SECTION VII – SPECIAL PRECAUTIONS
Keep out of reach of children.
Do not store near food or foodstuffs.
The LIQUID portion of the product is toxic to fish.
Keep children and pets out of storage and treatment areas.
The information and statements on this Material Safety Data Sheet is believed to accurately reflect the scientific evidence used in making the hazard deetermination, but is not to be construed as a warranty or representation for which we assume legal responsibility.
SECTION VIII – STORAGE
To extend product quality:
Avoid prolonged exposure to temperatures below 0* C to prevent package damage.
Avoid prolonged exposure to temperatures above 32* C to protect foam quality. Never store near heat
source or in direct sunlight.